Society for Testing and Materials (ASTM) methods will be used for .. Provider. From ASTM. D 5 Samples from powder coating lot to. Find the most up-to-date version of ASTM D at Engineering ASTM D Standard Guide for Testing Coating Powders and Powder Coatings.
|Published (Last):||9 September 2009|
|PDF File Size:||7.87 Mb|
|ePub File Size:||1.20 Mb|
|Price:||Free* [*Free Regsitration Required]|
I was set up your machine one week ago. About Us About Us. Practice G also speci? However, it is suggested that wstm otherwise agreed upon, panels for outdoor exposure should be prepared in accordance with Section 21 of this guide. Place the pointer between these two divisions. It should be noted that many of the methods used for characterizing a coating powder, such as gel time Section 16 and inclined flow Section d3415are primarily meant for the relative comparison of two coating powders, rather than to give a test value that can be interpreted as good or bad.
Add to Alert PDF. We have no amendments or corrections for this standard. Oil Analysis Equipment The test methods included are listed in Table 1.
In general, as the gloss of the powder coating is lowered, orange peel or other surface irregularities will become less noticeable. Problems such as changes in gloss, surface appearance, physical properties, and color contamination may occur if incompatible powders are mixed.
Control and monitoring wavelength. Information on current test procedures for pipe and reinforced steel bar coating powders and powder coatings can be obtained through their respective ASTM Subcommittees, A Already Subscribed to this document. Some coating powder chemistries can be inherently resistant d345 impact fusion d4351 though their tack temperature might be relatively low.
Please first log in with a verified email before subscribing to alerts. Your Alert Profile lists the documents that will be monitored.
ASTM D() – Standard Guide for Testing Coating Powders and Powder Coatings
The color difference equation used should be agreed upon between purchaser and seller. This test is 7 Selection of the methods to be followed must be governed by experience and the requirements in each individual case, together with agreement between the purchaser and the seller.
Typically, the cured weight loss from a coating powder will consist of water and low molecular weight organic compounds or blocking agents, or both. A superscript epsilon e indicates an editorial change since the last revision or reapproval.
Common terms associated with optical properties are de? Adhesion tests can also be used for testing the degree of attachment between a primer powder coating or other coating type and a second coat of coating powder that is, intercoat adhesion. Failure, when it occurs, is usually in the form of discoloration, changes in gloss, blistering, softening, swelling, or loss of adhesion. Interpretation of the test results will depend on the specific application in question and will also often depend on the chemistry of the coating powder used.
Standard Guide for Testing Coating Powders and Powder Coatings
Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters. Astj of the test results will depend on the speci? A spectrophotometer, the preferred instrument, measures re? Requirements within therecycled water. Proceed to Checkout Continue Shopping. It is the responsibility of the user of this standard to establish appropriate d33451 and health practices and determine the applicability of regulatory limitations prior to use.
Norma ASTM D()
Need more than one copy? Test compartment temperature control. Link to Active This link will always route to the current Active version of the standard.
Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. Individual reprints single or multiple copies of this standard may be qstm by contacting ASTM at the above address or at phonefaxor service astm.
Current edition approved Feb. We have no amendments or corrections for this standard. Diameter distribution of sampleclip. Observe the sharp division between solid and liquid. In the case of a thermoset coating powder, an accelerated storage stability test can allow a powder user e3451 predict the physical and chemical stability of a coating powder in order to determine its long term usability as a function of time and temperature. It is applicable to both thermoplastic and thermoset coatings, unless indicated otherwise.
Interpretation of the test results will depend on the specific application in question and will also often depend on the chemistry of the coating powder used. The results are most meaningful when a control powder, one whose? If the document is revised or amended, you will be notified by email. The spectrum of this device compared more favorably to sunlight than the enclosed carbon-arc.